Recent Posts

Pages: 1 2 3 [4] 5 6 ... 10
31
SolveigMM HyperCam / Re: Hypercam 5 Home will not load properly
« Last post by clskid on October 05, 2019, 05:57:43 AM »
That is correct.  I open Hypercam and the interface stays in the taskbar and i can only use it minimally from the taskbar.
32
Здравствуйте sanuchek,
К сожалению, не могу воспроизвести похожую проблему на имеющихся файлах, вероятно, что проблема специфична для конкретных файлов. Пришлите, пожалуйста, образец такого MKV файла, при резке которого происходит зависание и файл проекта резки в поддержку или мне личным сообщением, также, укажите ссылку на пост.
33
SolveigMM HyperCam / Re: Hypercam 5 Home will not load properly
« Last post by Maxim.Sakhankov on October 04, 2019, 12:51:08 PM »
Hello clskid,
Did I understand correctly, that you can't see the HyperCam's main interface on your screen?
34
SolveigMM Video Splitter / Re: Bug: Marker is some times placed incorrectly
« Last post by Maxim.Sakhankov on October 04, 2019, 12:39:56 PM »
Hello bleaurgh,
Unfortunately, I could not reproduce this behavior. Could you please give more details on this process? E.g.: is the playback on or off, what file types you use when the issue is reproduced? if it is specific to the file, please send this file to our tech support with reference to this topic.
35
Hello bleaurgh,
Thank you for the information, I reproduced the problem. I will post here when the issue is available.
36
SolveigMM Video Splitter / Re: Fade in/out effect?
« Last post by Maxim.Sakhankov on October 04, 2019, 11:54:19 AM »
Hello donb2016,
Currently, Video Splitter does not have this feature.
37
SolveigMM Video Splitter / Bug: Marker is some times placed incorrectly
« Last post by bleaurgh on October 01, 2019, 04:52:33 AM »
Ever since the redesign of the timeline, the marker seems to some times be incorrectly placed, compared to the video frame showed/playback indicator.

I haven't been able to pinpoint what causes this to happen, and have gotten used to press 'M' to add marker, and then check the timeline to see if I need to 'ctrl+z' to undo the marker if it shows up in the wrong place.
38
Save -> Save kept fragments separately -> Use mask for output file names, with mask like [source]_[n:4] will always start the numbering at 0002, not 0001. If using the save function multiple times, it will always skip one number.

Example:
Mark video into 2 kept sections.
Save kept fragments separately with [source]_[n:2] as mask.
Creates filename_02.ext
Creates filename_03.ext
Save again with same settings.
Creates filename_05.ext
Creates filename_06.ext

Would be nice if we could specify which number it should start at, or even reset the numbering.
39
SolveigMM Video Splitter / Fade in/out effect?
« Last post by donb2016 on September 24, 2019, 04:26:25 PM »
Is there a way to add fade in, fade out effect for clips that have been splitted?
40
SolveigMM HyperCam / Hypercam 5 Home will not load properly
« Last post by clskid on September 20, 2019, 11:11:55 PM »
I have installed Hypercam 5 Home Edition and was finally able to register it, however, it will not load properly.  The main menu box will only show in the taskbar and I cannot get it on my screen.
Pages: 1 2 3 [4] 5 6 ... 10